Skip to content

Part of the Golden Eagle Energy Group network

Electrical Infrastructure

The charger is the visible part. The project is everything behind it.

Service capacity, transformers, distribution equipment, and civil work frequently determine whether charging is feasible, how much it costs, and when it can be energized.

Existing electrical service

Every site starts with the service it already has: its voltage and phase (for example 208Y/120 V or 480Y/277 V three-phase), the ampacity of the main service, the building's connected load, and — most importantly — its measured demand.

Connected load overstates real use; measured demand from 12 months of utility interval or billing data shows actual peaks. Available capacity is roughly the service's usable rating minus measured peak demand, with margin, as determined by a qualified professional under the applicable code. A load study or monitoring period may be needed where data is missing.

Limitations and risks

  • Seasonal peaks matter — in Texas, summer cooling load often sets the building's maximum.
  • Spare breaker spaces do not mean spare capacity.

Transformers

The transformer serving a site may be utility-owned (common for smaller and many commercial services) or customer-owned (common on larger campuses with primary-voltage service). Either way, adding charging may exceed its loading capability.

Upgrades can mean a larger unit, a new dedicated transformer for charging, or new primary-voltage extension. Who pays, who designs, and how long it takes depend on the utility's line-extension and service policies. Lead times for transformers and switchgear have at times been many months; ask the utility and suppliers for current estimates rather than assuming.

Switchgear and distribution

Between the service and the charger sit switchboards, panelboards, overcurrent protection, and conductors. Charging may require new breakers, a new panel, a new switchboard section, or a separate service. Physical space in electrical rooms, working clearances, and the route from the room to the parking area all affect cost.

Conductor size depends on load, distance (voltage drop), and installation method; long runs to distant parking can materially increase cost.

Site and civil work

ElementWhy it matters
Trenching & conduitDistance from power source to parking is a major cost driver; boring may be needed under drives.
Concrete & padsDC equipment and transformers need foundations; pads affect layout.
Pavement restorationCutting and restoring asphalt or concrete adds cost and disruption.
Bollards & protectionEquipment must be protected from vehicle impact.
DrainageAvoid placing equipment where water collects.
AccessibilityAccessible charging spaces, routes, and reach ranges must meet applicable accessibility standards.
Parking layoutCable reach, space striping, and future expansion conduit.

Installing extra conduit ("make-ready") for future phases while trenches are open is usually far cheaper than trenching again.

Utility coordination

Engage the utility early. A typical path includes a service request or load letter describing the planned demand, utility review or load study, an upgrade scope and cost estimate if needed, design and scheduling, and energization. Provide realistic demand projections — managed peak, not nameplate sum — and phase timelines.

Common pitfall

Ordering equipment before the utility confirms capacity and timing can leave chargers installed and unpowered.

Networking and communications

Networked chargers report status, enable remote monitoring and diagnostics, apply pricing, and support load management. Many use the Open Charge Point Protocol (OCPP), which can allow switching software providers without replacing hardware — verify the version and certification supported.

  • Connectivity: cellular, Wi-Fi, or wired; garages may have poor signal.
  • Software integration with fleet telematics, parking, or building systems.
  • Contingency: define charger behavior when communications fail (e.g., default to a safe power limit; allow free or authorized-offline sessions).

Payments and user management

Pricing can be per kWh, per hour, per session, idle fees, or memberships, subject to applicable weights-and-measures and regulatory requirements. Payment options include apps, RFID, credit-card readers, and roaming agreements with other networks. Access control determines who can charge (employees only, residents, public). Reporting supports billing, taxes, and program compliance. Network and transaction fees recur for the life of the equipment.

Reliability and maintenance

Plan for preventive maintenance, remote uptime monitoring, cable and connector replacement, repair response times, service-level agreements, software updates, and eventual obsolescence. Ask what uptime a service contract actually guarantees and what remedies apply if it isn't met.

Who must be involved

  • Licensed electrical contractors perform installation.
  • Professional engineers prepare sealed designs where required by the scope or jurisdiction.
  • The utility determines service availability, upgrades, and interconnection.
  • Permitting authorities review plans and inspect work.
  • Qualified specialists for structural, civil, accessibility, and fire-safety matters.

Honest Charge's preliminary assessments are decision-support analyses. They are not stamped engineering designs and do not replace these parties.

Want this evaluated for a specific property?

An Honest Charge Site Analysis tests demand, electrical capacity, site conditions, and economics — and can conclude that you should not build.

How the analysis works